Difference between revisions of "Auto Assembler Example 1"

From Cheat Engine
Jump to navigation Jump to search
 
(One intermediate revision by the same user not shown)
Line 14: Line 14:
  
 
MyData:      // value will be set to address after ret
 
MyData:      // value will be set to address after ret
 
 
CreateThread(MyCode) // create new thread in open process
 
CreateThread(MyCode) // create new thread in open process
 
</pre>
 
</pre>
Line 20: Line 19:
 
This allocates 512 bytes and assigns the label MyCode to it.  It then lets the assembler know that MyData is used as a label later, and the autoassembler should set it's value to wherever it left off assembling code (the byte after ret).  It then registers MyCode and MyData as symbols, letting you enter them when you "Goto address" in the Memory Viewer window, or you can use an address of "MyData" or "MyData+4" for example in your cheat table.
 
This allocates 512 bytes and assigns the label MyCode to it.  It then lets the assembler know that MyData is used as a label later, and the autoassembler should set it's value to wherever it left off assembling code (the byte after ret).  It then registers MyCode and MyData as symbols, letting you enter them when you "Goto address" in the Memory Viewer window, or you can use an address of "MyData" or "MyData+4" for example in your cheat table.
  
It then assembles the code into the memory pointed to by MyCode (5F60000) and sets MyData to point to the address after it assembles the ret instruction (5F60016).  Finally CreateThread creates a new thread inside the process and starts executing code at the MyCode address.  The results are here, notice the 4 bytes after the ret are the 4 bytes at 4000000 inside the process and the 4 bytes after that are 78 56 34 12 from the second mov:
+
It then assembles the code into the memory pointed to by MyCode (5F60000) and sets MyData to point to the address after it assembles the ret instruction (5F60016).  Finally, CreateThread creates a new thread inside the process and starts executing code at the MyCode address.  The results are here, notice the 4 bytes after the ret are the 4 bytes at 4000000 inside the process and the 4 bytes after that are 78 56 34 12 from the second mov:
 
<pre>
 
<pre>
 
MyCode - A1 00004000                  - mov eax,[00400000] : [00905A4D]
 
MyCode - A1 00004000                  - mov eax,[00400000] : [00905A4D]

Latest revision as of 16:50, 17 July 2020

Take the following simple example:

alloc(MyCode, 512) // allocate 512 bytes inside opened process and store address in the MyCode label
label(MyData)      // MyData is defined later, set value at the location where the assembler hits it
registersymbol(MyCode) // make MyCode available everywhere
registersymbol(MyData) // make MyData available everywhere

MyCode:       // start assembling in allocated memory
mov eax, [400000]
mov [MyData], eax
mov [MyData+4], 12345678
ret

MyData:       // value will be set to address after ret
CreateThread(MyCode) // create new thread in open process

This allocates 512 bytes and assigns the label MyCode to it. It then lets the assembler know that MyData is used as a label later, and the autoassembler should set it's value to wherever it left off assembling code (the byte after ret). It then registers MyCode and MyData as symbols, letting you enter them when you "Goto address" in the Memory Viewer window, or you can use an address of "MyData" or "MyData+4" for example in your cheat table.

It then assembles the code into the memory pointed to by MyCode (5F60000) and sets MyData to point to the address after it assembles the ret instruction (5F60016). Finally, CreateThread creates a new thread inside the process and starts executing code at the MyCode address. The results are here, notice the 4 bytes after the ret are the 4 bytes at 4000000 inside the process and the 4 bytes after that are 78 56 34 12 from the second mov:

MyCode - A1 00004000                  - mov eax,[00400000] : [00905A4D]
05F60005 - 89 05 1600F605             - mov [MyData],eax
05F6000B - C7 05 1A00F605 78563412    - mov [05F6001A],12345678
05F60015 - C3                         - ret 
MyData - 4D                           - dec ebp
05F60017 - 5A                         - pop edx
05F60018 - 90                         - nop 
05F60019 - 00 78 56                   - add [eax+56],bh
05F6001C - 34 12                      - xor al,12

When you click the "Add Address Manually" button on the main Cheat Engine form (just above the table on the right below the scan info), you can use MyData as the address because we registered the symbol:

Aa simple ct1.png

And it will show in the table:

Aa simple ct2.png